مصنع اريتك للهندسة والتركيبات
يعد المصنع لتوريد و لتصنيع المحابس والفلانشات وجميع الصناعات المكملة لها من (دهانات - خراطات - لحامات) مقاولات التركيبات لخطوط الغاز والبترول والمياه والبتروكيماويات
يعد المصنع لتوريد و لتصنيع المحابس والفلانشات وجميع الصناعات المكملة لها من (دهانات - خراطات - لحامات) مقاولات التركيبات لخطوط الغاز والبترول والمياه والبتروكيماويات
Customizable floating and trunnion ball valves up to 80″.
Customizable double and triple offset (eccentric) butterfly valves up to 130″.
Customizable pressure balanced lubricated plug valves up to 36″.
Electric, pneumatic, gas over oil, hydraulic actuators and others.
أريتك
مصنع لتوريد و تصنيع المحابس والفلانشات وجميع الصناعات المكملة لها من (دهانات - خراطات - لحامات) وصناعات مقاولات و التركيبات لخطوط الغاز والبترول والبتروكيماويات والمياه
Our mission is to strive for the highest levels of product quality. Client satisfaction is our top priority, and we aim to actively take part in our client’s commercial success. We aim to deliver long lasting, high performing valves and provide after sales service to optimize our clients’ experience with our valves. We pride ourselves on the importance given to the safety of our employees and the environment, following all legislation, and providing frequent training sessions.
Read More
ARITEC, is a manufacturer and distributor of flanges from size ¼” up to 120” with years of experience and has based its value on quality, reliability, and fast delivery. Our goal is to satisfy a wide range of clients while maintaining the highest internationally accepted standards.
ARITEC, through its warehouse, generates a cycle of raw material procurement and manufacturing to single items of different sizes and specialized materials. This allows us to satisfy any client request and to offer a customized product all while maintaining quality management from start to finish.
ARITEC, is an experienced manufacturer and distributor of dismantling joints thaht offers a wide product range. With a large in-house stock and the ability to customize any project from 2″ uo to 120″ in size,Aritec in uniquely suited to provide fast solutions with reliable, high-quality Italian products to all of our customers around the globe.
The Riser is fixed to the jetty and is connected to the terminal piping system.
At the upper of the riser is secured a cubic structure supporting the inboard arm. Two bearings, two swivel joints concentric to the bearings and a 90° elbow flanged to the joints are installed inside of this cubic structure. Disassembling of just only the 90° elbow gives you a possibility to substitute joints and gaskets immediately.
Even without the 90° elbow and joints during the maintenance operation, the marine loading arm can work in each position without any limitations and dangers.
The Outboard Arm has a tubular section which is equal to the nominal diameter of the Marine Loading Arm.
An auto-levelling system composed by triple swivel and flanged elbow is connected at the end section of the outboard arm, this system allows the best coupling of the manifold to the vessel.
It is built by a self-supported structure anchored to the cubic structure by a thrust bearing.
A connection bearing for the main part of outboard arm and its joint, complete with a 90° flanged elbow is placed at the front end of the inboard loading arm.
Excluding the 90° elbow there is the possibility to replace rapidly the joint and gaskets of the outboard arm.
During the maintenance operation even without the 90° elbow and joints, the marine loading arm can operate in every position without limits.
The thrust bearing and the joint allow to the outboard loading arm a vertical rotation to be controlled and counterbalanced by a pantograph system with double counterweights.
The back end of inboard loading arm is composed by a fixed counter weight support system.
If needed, the loading arm can be equipped with a hydraulic motor and by means of an endless screws the hydraulic motor can be regulated to assure balancing of the loading arm in full and empty conditions.